#Drb3 emulator on sprinter code

This information is available from one of the following: If the vehicle isР’В equipped with SKIM obtain the vehicle Personal Identification Number (PIN) beforeР’В continuing with step 6. Step 5.Р’В If the vehicle is not equipped with SKIM then proceed to step 6. Look for РІР‚СљSKIMРІР‚Сњ in the list of modules.Step 4.Р’В Determine if the vehicle is equipped with SKIM. If the label on the controller is not legible, proceed to next step. NOTE:Р’В If the PCM is not operational, the part number can be obtained from the labelР’В on the old controller. Record the first ten (10) characters of the РІР‚СљPCM part #РІР‚Сњ on the repair order for laterreference.Step 2.Р’В With the ignition switch in the РІР‚СљRUNРІР‚Сњ position, determine the original part number of theР’В PCM currently in the vehicle. If the original PCM number begins with 05 no change to the flash selection process is required. This new number from the chart should then be entered into the Tech tools application as the orginal part number. NOTE: If your vehicle is a 2002 LH and the original PCM part number begins with 04,the technician should use the 2002 LH Part Number Reference chart above to determine the corresponding РІР‚СљNEWРІР‚Сњ part number. When the DRB IIIР’В® reboots to the MAIN MENU, proceed to Step 2.Follow the on screen instructions by selecting the РІР‚СљF4РІР‚Сњ key.A screen will appear requesting a РІР‚СљCOLD BOOTРІР‚Сњ.Simultaneously press the РІР‚СљMOREРІР‚Сњ and РІР‚СљYESРІР‚Сњ keys.To clear the memory from the MAIN MENU power upР’В the DRBIII and then: Step 1.Р’В Before beginning the reprogramming procedure, remove any old flash reprogrammingР’В files from the DRBIII memory. NOTE:Р’В If this flash process is interrupted/aborted, the flash should be restarted andР’В then follow the directions on the DRBIII emulator. Then turn the KEY to the RUN position and Press Page Forward toР’В begin the PCM flash session. Before pressing Page Forward to beginР’В the flash of the PCM Turn the Key to the OFF position and disconnect theР’В BCM. The BCM will need to be disconnected after the moduleР’В ID portion of the flash is complete. When flashing a 2002 РІР‚вЂњ 2004 LH vehicle the BCM may need to beР’В disconnected if experiencing failures during the flash of the transmissionР’В portion of the PCM. The module can only be reprogrammed to a moreР’В recent version of that calibration. Once a calibration isР’В selected and programmed, the controller cannot be reprogrammed to aР’В different calibration.

#Drb3 emulator on sprinter code

A Diagnostic Trouble Code (DTC) will beР’В set РІР‚вЂњ РІР‚Сљnot programmedРІР‚Сњ.Р”В¬AUTION:Р’В Extreme care must be taken when programming a calibration into a generic PCM. The PCMР’В will not operate the engine until it is programmed. Replacement ofР’В future PCMs will require programming utilizing the DRBIII and TechCONNECT. NewР’В modules will no longer be pre-programmed when received from MoparР’В®. MoparР’В® is currently phasing out pre-programmed PCMs for the vehicles listed. I have flash DVD for the wiTech VCI PodР’В DRB III, hopefully I will get it and can then do programming on a РІР‚СљswapРІР‚Сњ system.